Suggested Additional Purchase: Part # PBI-291 (Lock Nut)

Features & Benefits:-

* 34 Tooth Overdrive Pulley gives 6.4% Less RPM (187 RPM drop @ 60 MPH, high gear)

* Speedo Recalibration Unit NMZ-NSIM-01 is available if required.

* Long Life Steel

Tech Tips:-

* Does Not Fit Touring Models.

* Pulleys with more teeth than stock , rear axle must be adjusted forward.

* Each tooth change on transmission sprocket = + /– .125 inch at the Rear axle

* Each tooth change in belt length = + /–.280 inches at the rear Axle

* Not enough axle adjustment for the new pulley, use a belt with more (or less) teeth than stock.

1. Softail models 132 tooth (OEM is 133T) x 20mm rear belt is available BDL-SPC-132-20 (20mm) or OEM = 40074-07 / BDL-PCC-132-1 (1″)

2. Dyna Models 132 tooth (OEM = 131T) x 1″ rear belt is available

BDL-SPC-132-1

Proudly Manufactured in the USA by Andrew Products

* 2.61 Close ratio first gear set (2 pieces , 20T & 30T)

* Provides true close ratio shifting into 2nd.

* 10 kph of usable 1st gear.

* 2.61 close ratio 1st gear compares to 2.78 stock 1st gear ratio

* Made from high nickel alloy steel.

* Heat treated and shot-peened to give maximum durability & strength. * Lead-in ramps improve shifting and reduce wear on drive dogs & slots.

Tech Tips:-

* 2004 & later Sportsters cannot use the 1991-2003 gears

* Dual Fire High Output Andrews Super Volt Coil delivers 30,000+ volts.

* 4.8 Ohms all HD bikes with 12 volt point type ignitions.

* Also fits the very first 1979-80 HD type prestolite electronic Ignition

* Coils will produce more voltage than stock coils.

* Replaces OEM # 31609-65A

Proudly Made by Andrews Products!

* If you are installing cams in a shovel engine, the Andrews valve spring collars and related parts will make things go a lot smoother. The Andrews springs and collars are designed for easy installation and maximum reliability.

– Upper Spring Collars AP-271100 (high lift) or AP-276150 (Medium lift) , Lower Spring Collar AP-273120 and High Lift Springs AP-272110 are all available if required.

* Andrews Products pushrods are available for all Shovel engines using OEM or similar hydrualic lifters.

– Chrome Moly Push Rods AP-240030

* If you are installing cams in a shovel engine, the Andrews valve spring collars and related parts will make things go a lot smoother. The Andrews springs and collars are designed for easy installation and maximum reliability.

– Upper Spring Collars AP-271100 (high lift) or AP-276150 (Medium lift) , Lower Spring Collar AP-273120 and High Lift Springs AP-272110 are all available if required.

* Andrews Products pushrods are available for all Shovel engines using OEM or similar hydrualic lifters.

– Chrome Moly Push Rods AP-240030

BAI-D26-0205 – Trans Nut Lock Plate Kit; BT’92-06 & XL’91up

JGI-12067-A – Seal; Trans Main BT’L94-06 5spd Models Only

BCM-7342 – Main Drive Seal Spacer; BT’L94up 5spd

Features & Benefits:-

* 33 Tooth Overdrive Pulley 3% Less RPM

* Speedo Recalibration Unit DAK-SIM-1A is available if required.

* Long Life Steel

Tech Tips:-

* Fits 1986-2006 HD and aftermarket 5 speed transmissions as well as aftermarket 6 speed transmissions. Will NOT fit 2006up OEM 6 speeds.

* Big Twin 1986-93 require use of 1994 up seal and spacer.

Proudly Manufactured in the USA by Andrew Products

* This adjustable sprocket will change your timing from +4° for more torque, to -4° for less compression and for easier starting.

* Made in USA

Fitment:-

Twin Cam 2007 – 2017 Twin Cam engines, including 2006 Dyna & Milwaukee Eight engines.

Features & Benefits:-

* 30 Tooth Power Pulley gives 6.4% more RPM (200 RPM increase @ 60 MPH, high gear)

* Speedo Recalibration Unit NMZ-NSIM-01 is available if required.

* Long Life Steel

Tech Tips:-

* Pulleys with less teeth than stock, rear axle must be adjusted back.

* Each tooth change on transmission sprocket = + /– .125 inch at the Rear axle

* Each tooth change in belt length = + /–.280 inches at the rear Axle

* Not enough axle adjustment for the new pulley, use a belt with more (or less) teeth than stock.

1. Softail models 132 tooth (OEM is 133T) x 20mm rear belt is available BDL-SPC-132-20 or OEM = 40074-07

2. Dyna Models 130 tooth (OEM = 131T) x 1″ rear belt is available

BDL-SPC-130-1

3. ’09up FLH Models 139T belt # BDL-SPC-139-1

Proudly Manufactured in the USA by Andrew Products

* You’ll get more mid-range and top-end power for your street or drag bike

* These cams work with solid or hydraulic lifters, and the idle remains unaffected up to 6,000 rpm with stock valve springs.

* AB GRIND CAMS have an A intake plus a long duration exhaust for cooler running and high-end power

* A great bolt in cam for stock EV80 engines using state of the art design. Very strong, broad torque band which will pull hard from 2000 to 5500 RPM.

* EV27 cams run great with fuel injectors or carburetors!

* Works with stock valve springs

Suggested Additional Purchase:

Adjustable Pushrod Kit: # SS930-0052 or # AP-292245

Lifters: # FE-4061 or # SS33-5352

Cam Change Gasket Kit: 1970-1992 # JGI-25225-70-KX or 1993-1999 # JGI-25225-93-KX

Cam Bearing: SS31-4009

Cam Shim Kit: BCM-7200

Steel Breather Gear: SS33-4250 (OEM is plastic)